It’s just a YT video but if you don’t want to click the link you don’t have to let people know
It’s just a YT video but if you don’t want to click the link you don’t have to let people know
Even if they could go 407 km/h all the time they would have to change tires more often than filling the gas tank
This hits hard… I was just quoted 5000-8000€ repair for a sudden engine failure
Manjaro and Ubuntu surprised me how bad they are
“The more you buy the more you save” - NVIDIA
Seems like they both went to the same school
It appears I can in my phone app but not on PC unless I select copy link and paste it in new tab… Not sure why
Sam is great. Not fan of the newer games but I do play the older ones from time to time still
Most of the time I can’t tell a difference but with orchestra / classical music I can.
Also most of the time I listen to music when I’m in a factory with 75db-80db noise floor so it hardly matters how good headphones and source I’m listening to.
It’s just at home where I can fully enjoy my flacs with HD 650… Not that I bother listening to them too often anyways.
I’ll take good mp3 256kbps master over bad flac master any day though.
Thanks!
1.) will definitely give it a try 3.) I have set the amdgpu feature mask otherwise I wouldn’t even have access to the power limit, voltages, etc… but VRAM overclocking just does not work. Everything else seems to work fine.
I’m 100% sure it’s not a cable issue for many different valid reasons one of the main ones being that the cable is able to drive higher res monitor at higher refresh rate without issue.
Also if I just swap cables from my main monitor with the 2nd the same issue still happens with the 2nd monitor but only in Linux, never Windows.
Please bear in mind that custom tuning isn’t a guarantee between different driver versions; the voltage floor can shift with power management firmware changes delivered driver packages (this doesn’t overwrite the board VBIOS, it’s loaded in at OS runtime (pmfw is also included in linux-firmware)). I’d recommend testing with vulkan memory test with each Adrenalin update, and every now and then on Fedora too.
I’m aware. For now it seems to behave consistently. I observed higher avg clocks on Linux vs Windows with the same OC but then again it may be due to difference in monitoring SW or just polling rate.
To be fair when it’s time to upgrade the Linux support will be probably even worse since I would be upgrading to even newer stuff than what I have now.
I would hold on the conclusion for now. Steve from HW Unboxed tested both Zen 4 and Zen 5 with the “supposed” fix and both had improved performance so the rough difference between Zen 4 and Zen 5 remained almost the same as the issue was affecting both. We will need to see more tests though to draw a reasonable conclusion. We don’t yet know if this also affects older Zen 3 at all or not.
The monitors being flipped happened as well. I fixed that by flipping the DP cable order on the graphics card.
1.) IDK, this issue tends to manifest for me with different distros as well sometimes. Forgot to mention that it also happens if monitors go to sleep when inactive and on wake up the 2nd screen sometimes does not wake. That’s why I disabled sleep for monitors.
2.) So far works fine after disabling HW acceleration
4.) no need to waste both of ours time. The script now works fine but thanks for offer. I don’t even know what half of your sentence means :D
3.) On Windows I use MPT to further modify the cards behaviour like SOC voltages, clock, FCLK clock, TDC limits and power limits, etc… Basically I can easily squeeze 10% on top of the typical overclocking available via MSI Afterburner or AMD Adrenaline SW. #73rd place in TimeSpy for GPU score which is kinda ridiculous for air cooled card
Cyberpunk likes to draw a lot of current so my tweaks help alleviate the throttling caused by it in typical OC scenarios as the card hits current limit in the CP2077 benchmark more often than it hits the actual power limit. That’s why the lows on Linux are worse, it’s not related to CPU underperforming. I’d suspect that the lows would be actually better if I could uncap GPU TDC current limit on Linux. Averages would be likely still lower vs Windows due to lack of VRAM OC.
This is not really comparable and I would have to do proper test on both Windows and Linux with the same versions of the game but I’ve tested with the same settings which are FOV = 100, SSR = Low (because it performs like crap on higher settings for no visual benefit), everything else maxed out.
This is screenshot from the run I did in February with my Windows OC… (also had worse CPU and memory tune back then vs what I run now so results would be slightly better now as well).
And this is from right now on Fedora 40… not sure why CP detects it as Windows 10
Would be interesting to keep the same game versions and GPU,CPU,DRAM tune and do a direct comparison but I can’t really be bothered right now to mess with that. What’s important to me that it’s roughly in the same ballpark and there are no massive swings in performance so unless I keep a close eye on monitoring I can hardly tell a difference when playing.
Yes, I’m using the FOSS drivers. I’ll try to look at the logs next time it happens
RX 6800 XT
1.) I don’t think it’s a driver issue. For some reason the display just does not get picked up during boot. The system still behaves like there are 2 monitors connected though.
2.) Tried disabling HW acceleration in Steam, so far so good but haven’t used it for long enough to see if it’s completely fine.
3.) AMD changes VRAM timings with clock, it’s not just simple clock change, thats why also negative offset affects VRAM stability. I don’t think that CoreCTRL compensates for this with it’s VRAM tune.
“Should have hired taller people then”